Home > Error Code > Spa Error Code Flo

Spa Error Code Flo

Contents

So your pump comes on low speed. From here the troubleshooting takes you inside the spas service area and should be looked at by an experienced technician. Step 3. Oturum aç Çeviri Yazısı İstatistikler 41.299 görüntüleme 32 Bu videoyu beğendiniz mi? Here's our jumper. weblink

in the morning the FLO message was gone and it appeared to be functioning normally. Skip to main content Menu Pools Hot Tubs Bathrooms Service Pool Renovations Water Care Outdoor Living Parts and Accessories Store HomeSupport PostsMy Hot Tub Spa's Topside Control Panel Displays A FLO So the water is running through this heater bearer and we still have FLO we're going to say, "Hmm. Here's what to do if your spa throws a FL, FLO or FLOW error code at you.

Hydropool Flo Error

So, you pull one of the leads off. Both are secured with black plastic nut around the gray cable. The error codes above are related to a temperature sensor failure, overheat problems or a flow problem. All Rights Reserved.

Water level is also a common factor in flow errors, even with an insulating cover there is a lot of evaporation and that can lead to significant loss of water. I would see if you can test the 120v at the circ pump connector. See picture below for reference FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Sundance Hot Tub Flo Error They either need to be chemically cleaned over-night in filter cleaning solution or replaced if they are 1 year old or older.

BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" Flc Error Code On Hot Tub Now, it's going to send power to the heater to allow the tub to heat. UK Hot Tubs Ltd 47.275 görüntüleme 3:12 Hot Tub Filter Review | Arctic Spas - Süre: 1:49.

Flow switches are plumbed in line with the plumbing.

Used hot tub tonight, ran jets, when I went to put cover back on I noticed FLO code back on. Arctic Spa Hl Error Code A bit of a diagnostics that go into looking over the pressure switches themselves. This will reset the system. Back to FLO.

Flc Error Code On Hot Tub

Nigel July 22, 2016 Reply Anne-Marie what make a model spa do you have and what is the date built. http://precisionpool.net/2010/12/hot-tub-low-flow-error-causes-and-solutions/ Make sure the pump is not running and there's no movement in the tub. Hydropool Flo Error Locey Swim & Spa 37.033 görüntüleme 4:24 Master Spa FLO Code or No Heat Early 2000's Hot Tub How To FYI The Spa Guy - Süre: 2:54. Hydropool Hot Tub Error Codes You can check the switch by performing the test below.

It has maintained the temp for 3 days. have a peek at these guys We had no issues with it until recently-I went out to check on in and the water level was extremely low with a flor message on the panel. What those symptoms mean? I am wondering if its flow sensor? Where Is The Flow Switch On A Hot Tub

  • There's got to be something wrong with this pressure switch".
  • I have a cal spa classic select -41. 7000 control panel. 2, motors.
  • So what could be the problem, is there a relay issue on the motherboard ?
  • I have emptied and refilled the tub through the filter.
  • With a complete retail pool store in Amesbury. © 2014 Precision Pool Construction | 978-388-2585 | [emailprotected] Back to Top
Optimization WordPress Plugins & Solutions by W3 EDGE
  • The flashing FLO msg means the heat has been deactived to the spa.
  • Thread it out. FLO is coming on the top side. Hot Tub Accessories Hot Tub Covers Footer links 2 Discount Hot Tubs Online FAQs Footer links 3 Disclaimer Hot news Winterize Hot Tub Our Newsletter Subscribe Unsubscribe c 2015 HotTubSpaTips.com Hot check over here More hot tub repair tutorials and videos are here.

    Contact Your Dealer There are 100's of Arctic Spas stores worldwide.

    Thank you! Vita Spa Error Codes When I re-powered it, it went through it's priming cycle, but the pump never came on. Problem 2 LF low flow at certain times with no heat, and a dry warning, not sure what that means, but doesn't sound good.

    You could also have a poor connection at the Flow switch and or a bad Flow switch.

    You could try jumping out the leads where the pressure switch/flo-sensors plug into the board and see if the heater will click on. Sorry for long post. What we're gonna do right now is change a pressure switch. Hot Tub Flow Switch Troubleshooting It may be soiled/dirty/greasy, not to the naked eye.

    On either side of your spa's heater there are two sensors that read the water pressure flowing through the system. If your Topside is displaying a Solid FLO message you will have no water movement in the spa. Filter fine, pump good, runs good no sign of air , new sensors, still get LF and sometimes sensors indicate air bubbles, heater comes on intermittently but goes out when code this content Could it be the Flow Switch?

    First thing you're going to do when go to someones house and they call when they have a problem with FLO error is taking a look in the tub and we're If you hook a flexible hose up to the discharge side of the Flow switch and run this directly over the lip into the spa and receive no solid FLO msgs I did some more troubleshooting online and found to adjust the pressure switch wheel. Nigel August 21, 2016 Reply Damon check your temperature with a couple of external thermometers.

    Water was at 100 degrees this morning and everything was normal. FLO, FL, FLC, FL1, PS, Blinking Lights Pressure Switch or Flow Switch Failure. I have gotten the air out of system already. Cathy GMore Posts Filed Under: Troubleshooting a hot tub Tagged With: FLO, Flo error, hot tub broken, hot tub FLO Error, hot tub troubleshooting Comments Angie Williams says: December 11, 2012

    If you have a small circulation pump in your spa this could be clogged with debris and causing low flow. The COOL msg means the spa is a minimum 20 degrees below its set temperature. Be sure that there are no obstructions in the circ pump, heater and or the circulation line after the heater and Flow switch and make sure your filter is clean. The codes above are all related to flow issues or the pressure switch/flow switch and are the most common error codes.

    So - FLOW. I know the pump and heater are obstruction free because I had them both apart in the last few days. If you are seeing a Flashing FLO message, check to see that you still have water movement ie your circulation pump is still turning/waterfall is still running, jet and blower buttons