Home > Error Code > Spa Error Code Prr

Spa Error Code Prr

Contents

HOT = Circuit Board temperature has exceeded acceptable limit. Spacare.com 888-772-9887 Technical Assistance 405-622-4950 0 Item(s) | Total: $0 Home Shop SpaCare.com Spa Part Index Circuit Board Repair Spa Covers Spa & Hot Tub Covers Spa Cover Lifts Like our previous discussions on spa error codes, FLO and OH, the sensor codes Sn, Sn1, Sn2… are very much water flow dependent. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.SEoP = Sensor open or disconnected. check over here

The owners take a small town approach to delivering products that are high quality because they all have roots in rural Canadian communities. Gecko Spa Side Error Codes FLO Pressure switch failure, switch open FLC Pressure switch failure, switch closed Prr Temp sensor failure Prh Hi-limit sensor failure HL Sensor measuring 119 degrees FrE Underneath the spa, check that all valves are open (handles up). Switch closed while pump is deactivated.COL = Cool condition.

Balboa Hot Tub Error Codes

It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. Email check failed, please try again Sorry, your blog cannot share posts by email. %d bloggers like this: HomeTestimonialsBlogIndustry LinksPolicies, Warranties and DisclaimersService Area-Contact UsSpas / Hot Tubs & Swim SpasFilter Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat. OH Over heat.

  • Generated Tue, 06 Dec 2016 21:57:32 GMT by s_wx1193 (squid/3.5.20)
  • ILOC Interlock failure - possible pump or ozone spike. (---) Unknown water temperature. (Displays when first powered up after refill).
  • Low speed pump and heater will activate until spa reaches 65ºF.
  • If you are certain flow is present, but your pressure switch isn't activating you may want to remove it and be sure no debris is clogging it up.
  • Or, it could be a problem with the thermostat allowing the heater element overheat.

The Spa or Hot Tub Panel Displays: HL, HFL - This indicates that a substantial difference in temperature between sensors has been detected during heating. - This could indicate a flow Shut the spa power off, remove the filter and make sure all the jets are open. System will restart when temp. Balboa Spa Control Manual SE Spa operating in Standard-in-Economy Mode.

Heater is deactivated. Vita Spa Error Codes No More Headaches with Spa Solution! ICE Freeze condition. 55ºF detected. Please try the request again.

hot = Overheating, water over 112° F. Balboa Hot Tub Control Panel Codes Do not use spa when temperature is flashing or the OH message is displayed. drops. The system returned: (22) Invalid argument The remote host or network may be down.

Vita Spa Error Codes

Could indicate a flow problem.LF = Persistent low flow problems. (Displays on the 5th occurrence of "HFL" message with 24 hours). http://spatecservice.com/error-codes-digital-or-blinking-indicator-light.html Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously. Balboa Hot Tub Error Codes Make sure they aren't touching anything. Marquis Spa Error Codes Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice.

Check for debris on the heater element. check my blog One sensor has detected 118º F. It operates as well now as when I first purchased it. Brett Spa Side Error Codes For more information Regarding Brett Aqualine tech support click here OH Temp exceeds 118 degrees Fr Freeze condition - temp below 40 degrees FL Pressure switch Gecko Spa Pack Error Codes

Pressure switch is not working. SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking LightsAgain these can be caused by a flow issue. It automatically activates the pump (and the heater if necessary) to circulate the water and warm the plumbing. this content SE = Spa operating in Standard-in-Economy Mode.

Spa is shut down. Balboa Hot Tub Codes Sl The controller display is telling you that either the high limit or the temp sensor are open or shorted. FL Spa water is more than 20° F cooler than the temperature set point.

Do not enter the spa.

If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.Next, put your If display shows only this message (blinking) spa is shut down. How To Fix Flo Error Hot Tub These error codes are caused by a variety of reasons.

You can follow any responses to this entry through the RSS 2.0 feed. F6 Freeze protection. Switch closed while pump is deactivated. have a peek at these guys F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration EasyPak C = Celsius CL = Current Time of

SnS = Sensors out of balance. This could indicate poor flow or air bubbles in the heater. I am very satisfied and happy I purchased a PDC spa. ICE = Freeze protection.

The Spa or Hot Tub Panel Displays: HH, OOH, OH, OHS, OHt, HL, HiLi, Sn2, Sn3, tS, Ht, Blinking Lights At least one of the sensors has detected water temperatures of Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. th3/39 = On startup indicates water temperature less than 39° F. Ecn = Spa operating in Economy Mode.

Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. I wanted to thank you for your time explaining what I needed, as I wasn't 100% sure if what I was ordering was correct. The spa is at a temperature above 108° .

Contact qualified service technician. Sn3, HL, EO, E2, E3, Prh, Prr - these all refer to the heat sensors that are usually attached to your heater manifold. FINAL NOTE: The Hi Limit Sensor is located behind a shield on the stainless heater manifold and is the smaller of the two silver bullets.Other issues that can cause these error If alternating with temperature, it may just be a temporary condition.

Touch anybutton to reset the system.