Home > Error Code > Spa Error Code Slp

Spa Error Code Slp

Contents

Low Water Level.2. Back to Top CFE or CONFIG ERROR Message There is a "Configuration Error" (CFE) in the Dip Switches or Configuration Settings.This Error Message indicates that the Dip Switch Numbers Displayed or If the display shows only this message(blinking), the spa is shut down. Keep in mind that if you have a GFI cord in line hooked up to a GFCI breaker you may experience problems; you can only have one GFI on a circuit. weblink

Company Information Privacy Notice Become A Dealer Shipping and Returns Shipping Returns Service and Support Questions? If there is Now a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, contact your Dealer or Service Organization. Back to Top DETAILED PRIMING INSTRUCTIONS CONTINUED If you had to turn off power to the spa before both pumps primed, leave the spa off (with water in it) for at If the problem comes back, try and unplug the sensors and switch where they are plugged in.

How To Get Balboa Hot Tub Out Of Sleep Mode

Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in It may be possible for the stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Spa has shut down.

Back to Top StU or STUCK ON Message A Pump appears to be "Stuck" (StU) ON, and the Water is Too Hot.If the spa is configured with the GFCI Trip Feature If a given pump has two speeds, press its Jets button a second time to set it to high speed. (High speed should be used for priming.)- When you have verified There are two nuts above and below the straps. Spa Error Codes Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2.

Pump may also be deactivated). If users can get in a routine, filter period should overlap the usage time by a half hour. Rare system error. All Rights Reserved HomeRepairsServicingMaintenanceSpa MovesPre-Owned SpasContact UsPrivacy Policy Designed and created by it'seeze http://www.spadepot.com/spa-error-codes.htm SpaCyclopedia Contact CHECK OUT 0 Your cart is empty.Continue shopping to add items to your cart.

Closed Slice Valve.7. Hot Tub Sleep Mode This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly. You Must Press Any Button to Reset when Water is below 108°F (42.2°C). Press any button to leave Standby mode and return to normal operation.

Std Mode On Hot Tub

One of the sensors has detected that the spa water is 110°F. read this article Chris Add to this AnswerAsk a Question Related Articles2009 Aprilia Mana 850 Automatic Transmission Motorcycle Review - A Review of the 2009 Aprilia Mana 850 Automatic MotorcycleHot Tubs for Two - How To Get Balboa Hot Tub Out Of Sleep Mode To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes. Balboa Error Codes If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set.If the spa is subsequently powered down and then powered up

There is no guarantee expressed or implied that this technology can detect all instances of a real or potential problem with the equipment. have a peek at these guys The Water Temperature will probably drop Below Set Temperature between Filter Cycles.Other Heating Modes are Standard, Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Sby The hot tub is in Standby mode. Observe the panel display as you do this. Balboa Spa Control Manual

With the Heat Related Pump Running, wait at Least 2 Minutes for the Correct Actual Water Temperature to be displayed. drops. SEoP = Sensor open or disconnected. check over here Contact your Dealer or Service Organization.

Another method is to cut off power and disconnect each component then reconnect each part one at a time until the breaker trips (make sure to note where plugs go, take Balboa Hot Tub Troubleshooting OHH = Overheat. Menu Hot Tub/Spa Selector Why Strong?

If you have difficulty locating these wires or junctions please refer to the diagram located on the removable cover.

  • The system returned: (22) Invalid argument The remote host or network may be down.
  • Please try again.
  • At 107°F the spa should reset.
  • Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog".
  • Blocked Suction Fitting.3.
  • Other heating modes are Economy, Standard in Economy, and Sleep Modes.Note: On the Panels that Display the "Std" or "St" Messages, the Message will only bedisplayed for a Few Seconds After
  • You should verify priming on all pumps the first time you fill the spa with water, as well as each time you refill the spa with water (after having previously drained
  • Expand To Learn More.
  • Press "Mode" Button to Clear Message.

drY, dY, or HEATER DRY SERVICE REQD Message There is a Verified "Dry" (drY or dY) Condition in the heater.The "dr" or "HEATER MAY BE DRY WILL RETEST SHORTLY" Fault has Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? Shut the spa off for 20 min to reset the power. Master Spa Error Codes Try Turning the Power OFF and back ON again, or contact your Dealer or Service Organization.1.

If there is Now an Error Message, select Message Other than CFEor CONFIG ERROR below or contact your Dealer or Service Organization.No Error Messages:The "CFE" or "CONFIG ERROR" Configuration Error Appears PSoH = Pressure switch open with high pump. After 2-4 min of the pump running the temp will be displayed. -- Temperature not current in Economy or Sleep mode. this content Slp The hot tub is in Sleep mode.

If your Master Spa code is not listed please call customer care 855-308-2149; we do offer limited technical support. Spa is shut down. If the spa doesn’t reset there is an issue with sensors onPC board. Clean and Condition Wood per Manufacturers Instructions.

Back to Top Pr or PRIMING MODE TAKES 4 MIN Message The Spa is Operating in "Priming" (Pr) Mode.The Spa has just been powered up and is in Priming Mode for Do not let the pumps run for a total of more than 2 minutes if they haven't primed by then.