Home > Error Code > Spa Error Codes

Spa Error Codes

Contents

ToE Time out error. The J- 365 features four deep bucket seats and four smaller bench seats. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. HL = High limit switch tripped. check over here

Spa has shut down. CTI Spa Side Error Codes For more information regarding CTI tech support click here th1/39 On startup indicates temperature probe problem. HOT = Circuit Board temperature has exceeded acceptable limit. hot Overheating, water over 112° F.

Balboa Hot Tub Error Codes

Other issues that can cause these error codes is debris wrapped around the pump impeller, or one of the valves is not open up all the way. The main reason is water flow through the spa control system, if water is not flowing at a rate to satisfy the pressure switch, it will result in one of the Status of the heater element is unknown. Heat Related Pump Not Primed.

Heat Related Pump Not Running.8. Back to Top rdr or DRAIN WATER Message Time to "Drain Spa Water Reminder" (rdr).Appears Every 90 Days*. Indicates a shorted sensor and spa is shut down or an open sensor and heater is disabled.Contact a Jacuzzi hot tubs dealer or a service technician.Sn2Stands for “Sensor 2” and displays Coleman Spa Error Codes Fill out my Wufoo form!

The J-585 also has a very good step to enter the hot tub. Vita Spa Error Codes Contact dealer or a service technician if problem continues.OHOne of the sensors detected that the water in the hot tub is 112°F (44°C). th2/current temperature On startup indicates temperature probe problem. https://spacare.com/spasideerrorcodes.aspx drops.

drops.HL = High limit switch tripped. Gecko Spa Pack Error Codes The condition causes the circulation pump to turn off automatically if it’s running in order to avoid adding additional heat to spa water that could cause “Overheat” conditions. One sensor has detected 110°F. To prevent the heater from being turned on when there is no water running through, the heater is turned off and one of these message will be displayed indicating which pump

Vita Spa Error Codes

If the GFCI does not trip for some reason, the gFI fault will appear and the HOt flag will be set.If the spa is subsequently powered down and then powered up http://www.hottubworks.com/blog/spa-hot-tub-error-codes-fl-flo-flow-lf/ OH Overheating, water over 112° F. Balboa Hot Tub Error Codes If a given pump has two speeds, press its Jets button a second time to set it to high speed. (High speed should be used for priming.)- When you have verified Marquis Spa Error Codes Contact dealer or a service technician.BLB (Flashes in between water temperature and “blb”)Indicates that the Jacuzzi Hot Tubs needs a new UV bulb.Purchase new UV bulb from dealer and reset countdown timer.Summer

When the water isn't flowing like it should, the heater stops working, equipment overheats and water quality quickly suffers. check my blog Sn1 Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Too Many Closed Jets.6. Contact your Dealer or Service Organization to check the Switch Numbers or Setting Values Displayed, and Correct as Necessary to Match the Equipment in the Spa System, or Continue for a How To Fix Flo Error Hot Tub

dry Inadequate water detected in heater. (Displays on third occurrence of "dr" message). PSoL = Pressure switch open with low pump. Switch closed while pump is deactivated.COL = Cool condition. http://whistlemedia.net/error-code/spa-error-codes-help.html Could indicate a flow problem.

There are 3 groups of error codes; Flow codes, relating to water flow, Heater codes, and Sensor codes. Jacuzzi Error Code Fl1 If your spa is in fact overheating then it is caused by one of two things, either the temperature sensor is defective or the relays on the circuit board that operate SnS Sensors out of balance.

If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature.ICE = Freeze condition. 55ºF detected.

  1. Contact the dealer or service technician if the problem continues.Blinking Heater IconIcon flashes on and off to let you know that the temperature sensor has detected either a temperature difference of-20°F
  2. Ecn Spa operating in Economy Mode.
  3. OH Over Heat.
  4. The Heater and Pump will Operate Any time the Thermostat Demands Heat.
  5. SESH Sensor short, nonfunctional.
  6. Dirty Filter.5.
  7. drops.hot = Overheating, water over 112° F.
  8. dr Inadequate water detected in heater..
  9. Pressure switch is not working.SN = Non functional high temperature sensor.
  10. Back to Top PHL or PH IS LOW RAISE PH Message At the pH Sensor, the "pH Level is Low" (PHL).With a pH Sensor Installed in the System, the pH Level

If display shows only this message (blinking) spa is shut down. d) Replace the filter cartridge and verify the solution worked.4. ToE Time out error. Balboa Spa Control Manual Heater is deactivated.

Clean and Condition Spa Cover per Manufacturers Instructions. Snb Spa is shut down. Contact your Dealer or Service Organization. have a peek at these guys Pump may also be deactivated).

dry = Inadequate water detected in heater. (Displays on third occurrence of "dr" message). Pump may also be deactivated). Backyard BlastNews, Tips, Recipes, FAQ & Fun Jacuzzi Hot Tubs Error Codes & Information on June 11, 2015 in Hot Tub Maintenance Jacuzzi Hot Tubs and SpasThe family behind Jacuzzi Hot