Home > Smart Start > Smart Start Errors

Smart Start Errors

Contents

Possible causes: Error Code: 43 Description: Unable to delete the swap partition. If it does there is a good chance that the SmartStart module does not have a strong AT&T signal. Possible causes: Error Code: 18 Description: An unknown or no return code was returned from the SmartStart App. If error messages persist, repeat processes above followed by Uninstall, and re-install the app again from the Android Market. Source

Meaning: Unable to launch the SmartStart DOS Installation Utility. This could be because of... Meaning: Couldn't spawn ERASE from the CD-ROM in Upgrade mode. Possible causes: Error Code: 55 Description: Couldn't launch the System Partition Installation Utility.

Mysmartstart Error 12

Keep in mind that even if your Smart Phone doesn't use AT&T service the SmartStart module in the vehicle does. Error Code: 11 Description: The MSCDEX driver was not able to load. You need to renew your service by purchasing a new service plan at www.mysmartstart.com.

  • Social Bookmarks...
  • Possible causes: Error Code: 69 Description: Unable to compress System Partition files.
  • Error Code: 46 Description: Unable to write to the master boot record on the boot drive.
  • Meaning: Couldn't write to the master boot record on the boot drive in order to change partition information.
  • Meaning: There was no physical drives or logical drive on the primary disk controller.
  • Error message is: Your vehicle is not able to be remote started at this time.

Meaning: Unable to write to the master boot record of the disk drive to create the first disk partition. Possible causes: Error Code: 54 Description: Couldn't launch the System Partition Installation Utility. This can be caused by any of the following: 1) Device is outside coverage of the cell network 2) Device is powered down 3) Device is in the middle of resetting Smart Start Interlock Cheat Meaning: Unable to write to the master boot record on the boot drive in order to change partition information.

Make sure your vehicle is parked outside with a clear view of the sky. Smart Start Support Possible causes: Error Code: 38 Description: An unknown or no return code was returned from the SmartStart App. I renewed a device with an expired service plan and now I can’t send commands to vehicle. http://kb.viper.com/customer/portal/articles/694435-error-12?b_id=907 Possible causes: Error Code: 17 Description: Couldn't launch System Erase Utility.

Sep 10, 2012 05:37PM PDT Command received but failed to execute This message will occur when your SmartStart device receives the command you sent, but the installed system th... Viper Smart Start Customer Service Possible causes: Error Code: 13 Description: Couldn't launch the SmartStart Application in Upgrade mode( no SMART-2 installed). RESOLUTIONIf your Smart Phone does use the AT&T network and has a strong signal it is unlikely you will have this problem. Meaning: The return code that was returned from the SmartStart App was not set or was set to an unknown value during the main interviews.

Smart Start Support

Meaning: Unable to configure to network card(s) for use with SmartStart. Simply go to the link below and type in your zip code or even your exact address for a map of your area showing the relative quality of the AT&T signal Mysmartstart Error 12 Meaning: Unable to detect drive letter information for SmartStart. Smart Start Code Meanings Unable to launch Hardware Discovery in the Assisted Install path to configure IRC.

Meaning: Unable to write to the master boot record on the boot drive in order to change partition information. this contact form Check your handset connectivity for current data session (i.e. 3G network, 4G network, WiFi connectivity). Error 30 essentially means that your login or command request did not receive a server response. Yes I found this article helpful No I did not find this article helpful Powered by Desk.com Contact Us Email Us [email protected] http://assets1.desk.com/ false desk Loading seconds ago a minute ago Viper Smart Start Error Code 20

Meaning: Unable to decompress System Partition files in Assisted Install path. Possible causes: The ASPI driver that is required by MSCDEX was not able to load. Possible causes: Error Code: 70 Description: Unable to compress System Partition files. have a peek here Sep 10, 2012 05:45PM PDT Error 903 Error 903 means you are an active (logged-in) SmartStart user, and your app sent a command to a connected Smar...

The message "error sending command" is displayedCAUSEThis is most likely an issue with cellular coverage in your area. Sep 10, 2012 11:11AM PDT Error 35 Error 35 is generated when a Status or DTC data response was delayed (not received at server) longer than 30 s... Meaning: Couldn't spawn ERASE from the CD-ROM after previous erase didn't complete.

Possible causes: Error Code: 44 Description: Unable to remove the temporary SmartStart files.

Dezember 2012 um 19:27" data-utime="1356578829" data-shorten="1" class="_5ptz">26. Meaning: Unable to write to the master boot record of the disk drive to delete the swap partition. NOTE: you will need to re-enter your user name and password for this process. Occasional error 12 messages can be a normal occurrence caused by factors such as network coverage or congestion and vehicle location.

Directed must manage the exchange process to ensure the existing service plan is transferred to the new device. Meaning: Unable to remove the temporary SmartStart files from the system partition. http://www.wireless.att.com/coverageviewer/#?type=voice&3g=t This can give you a good indication of where you should expect the SmartStart system to work or not. Check This Out Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew

Sep 10, 2012 02:51PM PDT Error 25 The device is communicating but the last known location is more than 20 minutes old. Possible causes: Error Code: 52 Description: Unable to launch the SmartStart DOS Installation Utility. Possible causes: Error Code: 47 Description: Unable to detect drive letter information. Home › SmartStart Errors SmartStart Errors Articles My app says "if you had SmartStart your car would be running righ...

Meaning: Unable to launch the format utility to format the temporary swap partition.